Installing Two 60mm Fans on Xbox 360 Published bymanof360 on 2006-10-08 Category: Hardware Add-ons/Mods | Page Views: 12058
You will need:
- Xbox360 Opened
- Xbox360 stock fan removed
- Two 60mm Ledfans
- Phillips driver
- Something to cut and strip wires
- Dremel, or anything sharp enough to cut the corners off of a plastic or metal fan
Start by taking the new ledfan and cut off the plug. Cut an extra inch off the blue wire (just to get it out of the way) and strip the ends of the red and black wires.
Set the fan into place, it fits right onto a little shelf like it belongs there. The bottom two screws just line up perfectly, which is good because the top isn't even close. It does stay in place well with only two screws, so that isn't a problem.
Repeat the process with the second fan, by preparing the wires and screwing it into place next to the first one.
Here is what it looks like from the outside of the shielding, you can see how the bottom two holes line up with the holes in the shielding.
Now take the stock fan unit, and cut the plug off. Leave an inch or two of wire on the plug so you have enough to reattach new wires to it. Strip all four wires.
To connect the ledfan wires to the stock plug, twist the wires together. I refer to the left fan as the one on the left in my images, the one closest to where the fans plug into the motherboard.
Left ledfan red -> Stock plug red
Left ledfan black -> Stock plug black
Right ledfan red -> Stock plug brown
Right ledfan black -> Stock plug blue
Here is what it looks like from the outside of the shielding, you can see how the bottom two holes line up with the holes in the shielding.
Once the wires are all twisted together, insulate the bare wires with shrink tubing or electrical tape. Now plug the fans into the motherboard.
Optional: 12v install
When you connect new ledfans to the stock fanplug, it allows the 360 to control the speed of the fans based on current need. That keeps the noise level down nicely, but most ledfans do not push as much air as the stock fans. If your 360 ever has overheating issues, or if you just want it to run a bit cooler, you should connect the fans directly to 12v. Connect the red wires to 12v and the black wires to ground. You can access 12v and ground by connecting onto the dvd power harness, or by soldering to the points underneath the motherboard:
Your fans are now installed. The only problem is that the fans will be in the way when you try to put the airscoop back on. The top outside corners need to be cut off to fix that problem. I had no problem clipping off the corners with a sharp wire snips with them still screwed to the shielding. You may want to hack off those corners with a dremel or another tool before you screw the fans to the shielding. You can see I just removed a little bit from each outside top corner:
---> NOTE: If you install metal ledfans, you will either have to hack the airscoop or dremel the corner off the fans!
The fans are now completely installed. You can put the airscoop back on, and re-assemble your 360. Here are a couple pictures of how the fans look when they're running:
Registered Members: 118,957 Site Opened: October 2005 Page Views: 32,963,561 Forum Topics: 3,631 Forum Posts: 28,263 News Articles: 2,846 Comments: 144 Xbox 360 Achievements: 12,670 Xbox 360 Cheats Online: 1,841 Xbox 360 Games Online: 733 Xbox 360 Game Reviews: 103 Xbox 360 Links Online: 23 Xbox 360 Screenshots Online: 4,320 Xbox 360 Trailers Online: 470 Xbox 360 Tutorials Online: 74
Guests: 669 | 
Members: 15
Printer Friendly Page
manof360 on 2006-10-08
Registered Members: 118,957
